VAN ĐIỆN HIỆU CONTROLLI


THREADED PN16 2-3TBB
 THREADED PN16 MVGS2  THREADED PN16 VSB-VMB
 


 


 


SPECIFICATION

Two way valves 2TBB and three way valves 3TBB with bronze body can be used either for fluid control or detection in domestic hot water, air-conditioning, thermoventilation and heating plants, both environmental and industrial, and in machines for product thermal process. Three-way valves should be used only as mixing valves; angle way should never be usedfor control purposes.
2TBB are globe valves equal percentage characterised; the valve is closed when plug is lifted.
3TBB valves have a parabolic plug with modifi ed characteristic; if the plug is back the direct way is open. The angle way has a linear characteristic. It guarantees an excellent operation both as mixing as well as diverter valve.
These valves can be motorized by MVH and MVE actuators.
SPECIFICATION

Cast aluminium valve body PN10 designed to provide an optimised use in applications of fuel gas supply in industrial burners.
It is possible to calibrate the minimum fl ow rate through a pin on the valve body (see the fi gure below). The minimum calibration allows bypass control until complete close-off. Cast aluminium valve body. Lower closing cap in white plated brass. Manual brass plug to calibrate the minimum flow rate with double O-ring seal and cap. NBR Nitrile butadiene elastomer plug suitable for hydrocarbons, methane propane, butane, etc. with 20% glass loaded Noryl control flow rate profile. These valves can be motorized by MVB46P actuator, 3-point control with 1kΩ aux. reply potentiometer.
SPECIFICATION

Two or Three way valves with cast iron boby and brass plug which can be motorized with CONTROLLI MVB, MVH, MVH56FA/C, MVE actuators. Two-way VSB and three-way VMB valves can be used either for control or fl uid detection in air-conditioning, thermoventilation and heating plants, both environmental and industrial, and in machines for product thermal process.Three-way valves should be used only as mixing valves; angle way should never be used for control purposes. Cast iron valve body and prass internal parts; the temeprature allowed is -10T150°C (the max allowed temeprature decreases to 120°C if valves are motorised with MVB actuators).

DOWNLOAD CATALOGUES


2TBB-3TBB_DBL244e.pdf
 
DOWNLOAD CATALOGUES


MVGS2_DBL368E.pdf

DOWNLOAD CATALOGUES


VSB-VMB_DBL008e.pdf
 



FLANGED PN16 2FGA
 



FLANGED PN16 2FGA200B
 



FLANGED PN16 3FGB
 
 
 
SPECIFICATION

2 way cast iron valve body and stainless steel plug. 2FGA valves are used to control fl uids belonging to the group 2  (water, overheated water, steam) according to article 9 of 97/23/CE directive (PED) in air-conditioning, thermoventilation and heating plants and in industrial processes; therefore, they cannot be employed as safety valves. They consist in a two-way simple seat valve body to be assembledon an electrical bidirectional actuator. They have cast iron body, stailess steel internal parts and flanged connection PN16. Their size is DN15 up to DN100 and have equal percentage control flow characteristic.

SPECIFICATION

2 way cast iron valve body DN200 with stainless steel plug. 2FGA200B double seat valves are used to control fluids belonging to group 2 according to the article 9 of 97/23/CE (PED) directive in air-conditioning, thermoventilation and heating plants and in industrial process thermal machines; therefore, they cannot be used as safety valves.Group 2 regards water, overheated water, steam. They consist in a two-way double seat valve body to be assembledon bidirectional electrical actuator. G25 cast iron body, stainless steel internal parts and PN16 flanged connections; these valves can be motorized by MVH and MVE actuators.
SPECIFICATION

3 way valves DN15÷150 with cast iron body and bronze plug. 3FGB  valves are used to control fluids belonging to the group 2 (water, overheated water, steam) in accordance to article 9 of 97/23/CE (PED) directive, in air-conditioning, thermoventilation and heating plants and in industrial processes; therefore, they cannotbe used as safety valves. They consist in a 3-way valve body to be assembled on electricalbidirectional actuator MVH or MVE.
DOWNLOAD CATALOGUES

2F.._DBL316e.pdf
 DOWNLOAD CATALOGUES

2F.A150B-200B_DBL318e.pdf
DOWNLOAD CATALOGUES

3F.._DBL317e.pdf
 



FLANGED PN25 2FSA
 



FLANGED PN25 3FSA
 



FLANGED PN25 3FSAS
 
 
 
SPECIFICATION

2 way flanged valve with nodular iron valve body and stainless steel trims. 2FSA valves are used to control fluid in air-conditioning, thermoventilation and heating plants and in industrial processes; therefore, they cannot be employed as safety valves. They can be employed to control fluids belonging to groups 2 according to the article 9 of 97/23/CE directive (PED). Temperature range is -10°C - 230°C and size from DN25 up to DN65 are available.  2FSA valves are designed for a direct installation with MVE and MVH actuators.

SPECIFICATION

3 way valve with spheroidal cast iron body and stainless steel internal parts. 3FSA series valves are used to control fl uids belonging to the group 2 (water, overheated water, steam) in accordance to article 9 of 97/23/CE (PED) directive, in air-conditioning, thermoventilation and heating plants and in industrial processes; therefore, they cannot be used as safety valves. They consist in a 3-way valve body to be assembled on electrical bidirectional actuator. These valves can be motorized by Controlli actuators MVH and MVE series.
SPECIFICATION

3 way valve with spheroidal cast iron body and stailess steel internal parts. PN25 flanged 3FSA.S valves are used to control fl uids belonging to the group 1 (water, overheated water, steam, diathermic oil) in accordance to article 9 of 97/23/CE (PED) directive, in air-conditioning,  thermoventilation and heating plants and in industrial processes; therefore, they cannotbe used as safety valves. They consist in a 3-way valve body to be assembled on electricalbidirectional actuator. They can be motorized with Controlli MVH, MVHA/C and MVE series actuators.


DOWNLOAD CATALOGUES


2F.._DBL316e.pdf

DOWNLOAD CATALOGUES


3F.._DBL317e.pdf

DOWNLOAD CATALOGUES


3F.._DBL317e.pdf
 



FLANGED PN40 2FAA150B




FLANGED PN40 2FAA.B
 



FLANGED PN40 2FAA.P
 
 
 
SPECIFICATION

2 way valve DN150 with cast iron body and stailess steel internal parts. 2F.A.B series double seat valves are used to control fl uids belonging to group 2 according to the article 9 of 97/23/CE (PED) directive in air-conditioning, thermoventilation and heating plants and in industrial process thermal machines; therefore, they cannot be used as safety valves. Group 2 regards water, overheated water, steam. They consist in a two-way double seat valve body to be assembled on bidirectional electrical actuator. They can be motorized by MVH and MVE series actuators.
SPECIFICATION

PN40 Two-way Balanced Valves with steel valve body and stainless steel internal parts, DN25÷125. 2FAA.B balanced valve bodies are designed for use in air-conditioning, thermoventilation and heating systems and in industrial process and they cannot be used as safety valves. They can be employed to control fl uids belonging to group 2 according to the article 9 of 97/23/CE directive (PED). Group 2 includes water, overheated water, steam.
The peculiar characteristic of such valves is they can operate under high close off pressure and wherever low leakage is required. This makes them particularly suitable in applications with high pressure and high ΔT, such as overheated water (i.e. remote control, boiler supply) and steam. They can be motorized by MVH, MVHA/C and MVE series actuators.
SPECIFICATION

2 way valve with steel body and stainless steel internal parts.  2FAA.P series valves are used to control fl uids belonging to the group 1 (water, overheated water, steam, diathermic oil) to article 9 of 97/23/CE directive (PED) in air-conditioning, thermoventilation and heating plants and in industrial processes; therefore, they cannot be employed as safety valves. They consist in a two-way simple seat valve body to be assembled
on an electrical bidirectional actuator. They can be motorized with MVH and MVE series actuators.

DOWNLOAD CATALOGUES


2F.A150B-200B_DBL318e.pdf

DOWNLOAD CATALOGUES


2FAA.B_DBL319e.pdf

DOWNLOAD CATALOGUES


2F.._DBL316e.pdf
 




ACTUATORS LINEAR ELECTR0-MECHANICAL MVB
 




ACTUATORS LINEAR ELECTR0-MECHANICAL MVE
 




ACTUATORS LINEAR ELECTR0-MECHANICAL MVH
 
 

 
SPECIFICATION

Globe valves actuator for application in heating and cooling system.MVB actuators are equipped with a reversing synchronous motor and an electronic board available in three different models respectively for floating control, proportional control (potentiometric) and proportional control (voltage or current).  MVB actuators are available with timing of 30s, 60s and 370s.
Due to their versatility MVB actuators can be mounted both on “Controlli” globe valves up to VSB/VMB DN 2” as well as on different manufacturer valves, having stroke from 10.8 to 20 mm. All models are equipped with a manual override device
SPECIFICATION

The MVE is a flexible electro-mechanical actuator for the control of two and three way globe valves in: Heating and Cooling systems, Air handling units, District Heating plants, Industrial Temperature Control systems. The MVE can be controlled either by a proportional (modulating) signal or by an increase/decrease (Floating) signal simply changing switch settings on the field. It is designed for an easy installation to any CONTROLLI flanged valve. Linkage kits are available for threaded valves as well as for valves of other manufacturers.
SPECIFICATION

Globe valves actuators for heavy duty extremely hight temperature (up to 350°C) or extremely low temperature (below -20°C) application in air conditioning systems and industrial processes. MVH is available in several different models with force from 700 N up 3000 N with and without spring fail-safe mechanism. It is designed for direct coupling with the complete range of Controlli Flanged valves 2F/3F with U-Bolt connection.



DOWNLOAD CATALOGUES


MVB_DBL005e.pdf

DOWNLOAD CATALOGUES


MVE2xx_DBL394e.pdf

DOWNLOAD CATALOGUES


MVH.F_DBL334e.pdf
 





ACTUATORS LINEAR ELECTR0-THERMAL MCA
 





ACTUATORS LINEAR ELECTR0-THERMAL MVR
 





ACTUATORS LINEAR ELECTR0-THERMAL MVX
 
 
 
SPECIFICATION

MCA actuators are designed for mounting on manifolds for floor, ceiling and wall radiant panels on heating or air conditioning plants.
MCA can be used for On/Off (2-wire) control system in heating, air-conditioning and ventilation systems and for distribution manifolds for individual room temperature control of radiant heating & cooling systems.
Where required, auxiliary microswitches are normally open type. In case you need to operate with a normally closed micro-switch, please contact our Technical Dept.
Thanks to the innovative adaptive feature, this actuator is almost universal and suitable to the majority of zone valves and manifolds in the market. The integrated auxiliary switch allows direct or indirect (with relay) operation of a pump or a fan control unit.

SPECIFICATION

MVR actuators are designed for mounting on manifolds for floor, ceiling and wall radiant panels on heating or air conditioning plants. MVR actuators are of electro-thermal type and are controlled by an on-off signal or, 24 Vac models only, also by pulse width modulation. Actuators are powered by the control signal; this causes the heating of a thermostatic element. Consequently a small piston comes out and, opposing to return spring, lowers the valve stem. MVR...M models are equipped with an auxiliary microswitch. The microswitch has the contact closed when the actuator isunpowered.
SPECIFICATION

Electro-thermal actuators for fan coil valves PN16 Micra® and Micra® Kvs 4-6.

MVX21R - MVX41R - MVX57

electro-thermal actuators series MVX with stroke indicator for VSX-VMX and VTX valves. 2mt bipolar/tripolar cable (0,35mm2) and IP44 protection. Actuators MVR21R and MVX41R are on/off, MVX57 is proportional 0-10Vcc.

MVX22R - MVX42R - MVX52

Actuators series MVX. Electro-thermal actuators for V.X valves with Kvs 4-6. Stroke end indicator, bipolar/tripolar cable 2mt (0,35mm2) and protection IP44.

DOWNLOAD CATALOGUES

MCA_DBL400e.pdf

DOWNLOAD CATALOGUES


MVR_DBL310E.pdf

DOWNLOAD CATALOGUES


MICRA_DBL199e.pdf


TRỤ SỞ TP.HCM:
Địa chỉ   :  189 Nguyễn Văn Thủ, P.Đakao, Q.1, TP.HCM
Tel   :   (08) 3910 7080 / 81/ 82
Email  :  info@toangiaphat.com

VĂN PHÒNG ĐÀ NẲNG:
Địa chỉ   : 150 Bế Văn Đàn, Thanh Khê, Đà Nẳng
Tel        : 0909 606 568
Email   :   info@toangiaphat.com

VĂN PHÒNG HÀ NỘI :
Địa chỉ   : số 4 ngõ 44/1 Đỗ Quang,  Trung Hòa, Cầu Giấy, Hà Nội
Tel         :   
0976 421 216
Email   :   info@toangiaphat.com

Lượt truy cập:  7054448
Online:  15